Tuesday, June 6, 2017

5/16 Impedance

    The purpose of this lab to find the actual impedance of the circuit through the experiment method. And also observe the effect of the impedance to the circuit.

1. Pre Lab calculation:


2.This is the actual set up of our lab
The following photos are the result of our experiment

100 ohms and 5K Hz and no phase shift

                                                  I = 13.27mA   V = 1.367V



100 ohms and 5K Hz and 32.5 degree phase shift

I = 34mA     V = 1.06V


100 ohms and 5K Hz and 82.8 degree phase shift


I = 6.2mA    V = 2.05V

Summary 
     In today's class, we are introduced the concept of impedance. We can calculate the impedance of capacity and inductor. Then, trade them as resistance.

Monday, June 5, 2017

5/11 Phasors: Passive RL Circuit Response

         The purpose of this lab is to observe the unique function of passive RL circuit. We need to know how to calculate in the phasor domain

Pre lab:
These are the calculations we did for this lab.

The cutoff frequency for 1mH and 470Ohm resistor is 47000/2Pi = 7480Hz
The frequency with one tenth of cutoff frequency is 748Hz
The frequency with ten times of cutoff frequency is 74800Hz



This is the actual set up of our experiment.

The following photos are the result of our lab

1. the phase difference is (3.102)/(13.5)*360 = -82.72degree,

2. the phase difference is (16.87)/(135)*360 = -44.9degree,
3. the phase difference is (0.03)/1.45 = -7.448degree,

summary
    In today's class ,we learned how to convert the time domain to the phasor domain. Then, we can do the futher calculation.The following are some rule of the converting:




5/9 RLC Circuit Response

1. Provide the differential equation governing the circuit.

2. Attach plots of the input step function you applied to the circuit and the resulting circuit step response.


3. Provide the damping ratio, DC gain and natural frequency.
damping ratio:0.25
DC gain: 8
Natural frequency:  10105.8 Hz

4. Compare your measured vs expected parameters
They are pretty close.

Summary
    In today's class, we keeping learning the concept of RLC circuit. There are two different types of RLC circuit one is parallel and the other one is series. Different RLC have different equation to do the calculation.

5/2 Series RLC Circuit Step Response

          The purpose of this lab is to find the DC gain and phase shift through the experimental method. Then, compare with the theoretical value we calculated in the pre-lab

1. Provide the differential equation governing the circuit.
2. Attach, plots of the input step function you applied to the circuit and the resulting circuit step response.
According to the picture, raise time: 1.241ms
overshoot:3.5ms
oscillation frequency: 23485Hz

3. Provide the estimate of the damping ratio, natural frequency, DC gain, and damped natural               frequency.
damping ratio: 5*10^-7
DC Gain: 2.383

Summary
    In today's class we learned how to calculate Series RLC Circuit. We learned the formula to calculate the w and α. Then use those data to calculate the current and voltage.

4/25 Inverting Differentiator

        The purpose of this lab is to verify the function of inverting differentiator. We need to find the out voltage and input voltage through the experiment. Then, compare these values with the theoretical value.

1. Provide the input-output relation  for the circuit:
 the relation is showed in the photo.

2. Provide a schematic of the circuit you implemented:

The actual resistance we used in the lab is 665

3. Attach an image of the oscilloscope window for the 100 HZ sinusoidal input:

4. Attach an image of the oscilloscope window for the 250 HZ sinusoidal input

5. Attach an image of the oscilloscope window for the 500Hz sinusoidal input 

6. Provide a table showing the expected output voltage amplitudes



Summary
               In today's class, we introduce the definition of differentiator. A  differentiator is a circuit that is designed such that the output of the circuit is approximately directly proportional to the rate of change (the time derivative) of the input. An active differentiator includes some form of amplifier. A passive differentiator circuit is made of only resistors and capacitors.

Sunday, April 30, 2017

4/18 Passive RC Circuit Natural Response

         The purpose of this lab is to build the actual RC circuit circuit. Then find the nature frequency and outout voltage.
1. Provide the initial capacitor voltages and time constants for the circuits


2. Provide below a schematic of the circuit you implemented, including actual resistance and capacitance values used in your circuit. A picture of your whiteboard sketch is adequate.
This is the actual circuit we built during the experiment:
The actual resistance for R1 = 0.977 ohms and R2 = 2.16k ohms.

3. Attach an image of the oscilloscope window,showing the capacitor voltage response for the circuit of Figure2(a)
from the graph we measured 5 time constant = 0.343s
And from the pre-lan we calculated 5 time constant = 0.352s
% error = (0.352-0.343)/0.343*100% = 2.56%

Figure 2(b)

From the graph we measured 5 time constant = 0.08158s
From the pre-lab we calculated 5 time constant = 0.0756s
% error = (0.08158-0.0756)/0.08158*100% = 7.91%



Summary 
     In today's class, we were learning how to find the equivalent for the capacitor and inductor. For the inductor, it is the same as the resistance when inductors are in parallel and series. However, the capacitor is in the inverse. Also, we learned two equations for the inductor and capacitor:

The follow photo is the example we did during the class: 


4/13 Capacity Voltage-current Relations

         The purpose of this lab is to verify the voltage function of capacity. We need to use the analogy to find the actual voltage function VS time. Then compare our graph on the whit board.

1. Attach the sketched of the vapacitor voltage and current for both sinusoidal and triangular inputs

2. Attach an image of the oscilloscope window, showing the capacitor voltage and current waveforms and the measured amplitudes of the waveforms for a 1K HZ sinusoidal input.


The picture is when applying a sinusoidal input voltage with frequency = 1kHz, amplitude = 2V, and offset = 0V to the circuit.

3. Attach an image of the oscilloscope window, showing the capacitor voltage and current waveforms and the measured amplitudes of the waveforms for a 2K HZ sinusoidal input.


4. Attach an image of the oscilloscope window, showing the capacitor voltage and current waveforms and the measured amolitudes of the waveforms for a 100Hz triangular input.



Summary
       During the class we learned the basic concept of capacitor. We treat a capacitor as open circuit in the beginning because there is no current there.
 these are some examples we did in the class.